1999.5–2003 7.3L POWERSTROKE TURBO UPGRADE GUIDE: STOCK VS. STOCK PLUS VS. STAGE 1 VS. STAGE 2

Aug 27, 2026

1999.5–2003 7.3L Powerstroke Turbo Upgrade Guide: Stock vs. Stock Plus vs. Stage 1 vs. Stage 2

Written By: Andrew Kolonay

The 1999.5–2003 7.3L Powerstroke responds well to the right turbocharger upgrade, but the right choice is not automatically the largest or most expensive turbo that will bolt into the factory location. A turbocharger must be matched to the truck’s injectors, fuel delivery, high-pressure oil system, tuning, intake, exhaust, towing requirements, and intended power level. Installing more airflow capacity than the engine can use may add cost and complexity without improving the way the truck drives, while asking a stock-size turbo to support substantially more fuel than it was designed for can push the turbocharger outside its most useful operating range.

SPOOLOGIC offers four direct-fit, wastegated GTP38 turbocharger choices for the Late 1999 through 2003 7.3L Powerstroke platform: the SL-100-006 Stock, SL-100-007 Stock Plus, SL-100-008 Stage 1, and SL-100-009 Stage 2. SPOOLOGIC also offers the SL-100-010 as a separate non-wastegated performance option for specialized combinations. Each step changes more than the name on the box. Compressor design, turbine-housing capacity, wastegate configuration, exhaust back-pressure valve configuration, bearing system, tuning requirements, and supporting-modification needs all affect how the turbocharger behaves.

This guide explains those differences and helps identify which turbo best fits a stock daily driver, towing truck, mildly modified street truck, or fully supported higher-output build. Installation procedures will be covered separately so this article can stay focused on choosing the correct turbocharger.

Confirm You Have the 1999.5–2003 7.3L Powerstroke Turbo System

This guide is focused on Late 1999–2003 Ford F-250, F-350, F-450, and F-550 Super Duty trucks equipped with the later 7.3L Powerstroke turbo system. For a 1999 truck, SPOOLOGIC identifies the later application as an engine build date of 12/8/1998 and after. The corresponding engine serial-number break begins at 896,813.

Early 1999 trucks use a different turbocharger, pedestal, exhaust inlet arrangement, up-pipes, intake crossover, and charge-air connections, so they require their own turbo family. Before ordering for a 1999 truck, use the Early 1999 vs. Late 1999 7.3L Powerstroke Turbo Identification Guide to confirm which system is currently installed.

1999.5–2003 7.3L Powerstroke Turbo Comparison

Turbo	Compressor	Turbine and Bearing System	Wastegate and EBPV	Calibration Requirements	Best Use
SL-100-006 Stock	60/80mm 5+5 cast aluminum	Factory-style turbine with upgraded journal-bearing internals	Approximately 22 PSI actuator; retains factory EBPV	Stock-style replacement	Daily driving, towing, work trucks, fleet use, and restoration
SL-100-007 Stock Plus	60/80/84mm 5+5 billet aluminum	Factory-style turbine with upgraded journal-bearing internals	Approximately 22 PSI actuator; non-EBPV pedestal and outlet	No custom tuning required solely for installation	Daily driving, towing, and mild performance use
SL-100-008 Stage 1	60/80/84mm 5+5 billet aluminum	Factory-style turbine wheel with upgraded journal-bearing internals and 1.0 A/R turbine housing	30 PSI actuator; non-EBPV pedestal and outlet	Custom tuning strongly recommended; boost fooler required	Tuned street trucks and moderately modified combinations
SL-100-009 Stage 2	66/88/94mm 6+6 billet aluminum with 4-inch anti-surge inlet	76/70mm turbine, 1.0 A/R turbine housing, and hybrid ceramic dual ball-bearing cartridge	30 PSI actuator; non-EBPV pedestal and outlet	Custom tuning and boost fooler required	Properly supported higher-output builds with increased fueling

The wastegate ratings in this table describe the actuator configuration supplied with each turbocharger. They are not guaranteed manifold-boost numbers and should not be treated as universal boost targets. Actual boost depends on exhaust energy, injector output, tuning, engine load, elevation, intake restriction, exhaust restriction, wastegate control, and the condition of the complete charge-air system.

How to Read the Compressor-Wheel Measurements

Compressor-wheel measurements are commonly listed as inducer diameter, exducer diameter, and, when applicable, tip diameter. Those numbers are useful, but one measurement by itself does not determine how much air a compressor can move or how the complete turbocharger will behave on the engine. Blade count, blade shape, hub design, tip geometry, compressor housing, inlet design, shaft speed, pressure ratio, turbine wheel, and turbine-housing A/R all affect the useful operating range.

This is particularly important when comparing Stock Plus and Stage 1. Both the SL-100-007 Stock Plus and SL-100-008 Stage 1 use a 60/80/84mm 5+5 billet compressor wheel. The Stage 1 does not use a 7+7 compressor wheel. The primary differences are on the turbine and boost-control side: Stage 1 uses a 1.0 A/R turbine housing and upgraded 30 PSI wastegate actuator, while Stock Plus retains the more conservative factory-style turbine configuration and approximately 22 PSI actuator.

Stage 2 makes a much larger physical jump to a 66/88/94mm 6+6 billet compressor, 4-inch anti-surge inlet, upgraded 76/70mm turbine wheel, 1.0 A/R turbine housing, and hybrid ceramic dual ball-bearing cartridge. Compare the complete compressor, turbine, bearing, and boost-control package rather than assuming that a stage designation or a single compressor measurement tells the whole story.

Why the Biggest Turbo Is Not Always the Best Turbo

A turbocharger does not create a fixed amount of horsepower by itself. It supplies compressed air, while the injectors and fuel system supply the fuel needed to produce power. The calibration determines how those systems work together. A larger compressor can support more airflow, but the engine must have enough fuel and exhaust energy to move the turbo into its intended operating range. Without the correct combination, a larger turbo may spend much of its time below the airflow range where it provides a meaningful advantage.

The turbine side matters just as much as the compressor side. A larger turbine wheel or higher-A/R turbine housing can provide more exhaust-flow capacity and reduce restriction at higher output levels, but it generally requires more exhaust energy to accelerate. A smaller factory-style turbine configuration usually responds quickly in a stock or mildly modified truck, but it eventually becomes a limitation as fueling and exhaust flow increase.

The Stock Plus and Stage 1 SPOOLOGIC turbos illustrate this difference clearly. They use the same 60/80/84mm 5+5 billet compressor dimensions, but Stage 1 pairs that compressor with a 1.0 A/R turbine housing and 30 PSI actuator. Stage 2 moves farther by using a larger compressor, larger turbine wheel, 1.0 A/R turbine housing, and ball-bearing center section as part of a complete higher-output rotating assembly.

Bearing design also changes the character of the turbocharger. The Stock, Stock Plus, and Stage 1 models use upgraded journal-bearing internals with extreme-duty bronze-alloy journal bearings, a 360-degree thrust bearing, step-gap seal rings, and high-speed VSR balancing. Stage 2 moves to a hybrid ceramic dual ball-bearing cartridge inside a finned aluminum center section. The ball-bearing system reduces bearing friction and helps the larger rotating assembly respond more quickly than a comparable journal-bearing arrangement, but it does not eliminate the need to match the Stage 2 compressor and turbine to the engine’s fueling and intended operating range.

SPOOLOGIC SL-100-006 Stock Turbocharger

The SPOOLOGIC SL-100-006 Stock GTP38 Turbocharger is the correct starting point when the goal is to replace a worn, leaking, damaged, or failed factory turbo without changing the basic character of the truck. It uses a 60/80mm 5+5 cast aluminum compressor wheel, a factory-style GTP38 turbine, an internally wastegated turbine housing, and an approximately 22 PSI factory-style wastegate actuator.

The 5+5 cast compressor design helps reduce the surge tendency associated with the original-style 9-blade cast wheel while remaining a stock-replacement configuration rather than a horsepower-focused upgrade.

The Stock turbo is also the only option in the main four-turbo lineup that retains the factory exhaust back-pressure valve. The included EBPV pedestal and outlet maintain the original cold-weather warm-up system and factory-style exhaust arrangement. That makes the SL-100-006 the most appropriate choice for a restoration, fleet truck, work truck, stock tow vehicle, or owner who wants the truck to operate as close as possible to its original configuration.

It is not the right choice for someone specifically looking for a billet compressor, a 30 PSI actuator, an EBPV delete, or the additional turbine capacity required by a more aggressive injector and tuning combination.

SPOOLOGIC SL-100-007 Stock Plus Turbocharger

The SPOOLOGIC SL-100-007 Stock Plus GTP38 Turbocharger is designed for owners who want a meaningful but conservative step above a standard stock replacement. Its 60/80/84mm 5+5 billet aluminum compressor wheel increases airflow capability while retaining the responsive factory-style GTP38 turbine configuration and approximately 22 PSI wastegate actuator.

The Stock Plus also changes the exhaust-side supporting hardware. It includes a non-EBPV pedestal, non-EBPV outlet plate, and EBPV terminator. Removing the valve flap from the exhaust path reduces restriction and eliminates the factory EBPV assembly as a possible exhaust leak, oil leak, or future service point. The tradeoff is that the truck no longer retains the original exhaust back-pressure warm-up function. Owners who place a high value on factory cold-weather operation or use an EBPV-based aftermarket braking strategy should consider that difference before choosing Stock Plus over the Stock turbo.

For a mostly stock truck, lightly modified daily driver, or tow rig that needs a new turbo and would benefit from a billet compressor and simplified non-EBPV exhaust arrangement, Stock Plus is usually the most balanced mild-performance choice. No custom tuning is required solely to install the turbo. Tuning may still improve the truck when other performance modifications are present, but Stock Plus does not carry the Stage 1 requirement for a boost fooler or the Stage 2 requirement for a fully matched custom calibration.

SPOOLOGIC SL-100-008 Stage 1 Turbocharger

The SPOOLOGIC SL-100-008 Stage 1 GTP38 Turbocharger is the next step for a truck that has moved beyond a mild Stock Plus combination. It uses a 60/80/84mm 5+5 billet aluminum compressor wheel, factory-style GTP38 turbine wheel, 1.0 A/R internally wastegated turbine housing, and upgraded 30 PSI wastegate actuator.

The Stage 1 compressor has the same blade configuration and dimensions as the Stock Plus compressor. Stage 1 is differentiated by its 1.0 A/R turbine housing and 30 PSI actuator, which give the exhaust and boost-control sides more capacity for a tuned, moderately modified combination. The 1.0 A/R housing can support greater exhaust flow at higher output levels, while the 30 PSI actuator provides a different wastegate-control range than the approximately 22 PSI actuator used on Stock Plus.

Custom tuning is strongly recommended so fueling, boost control, injector behavior, and the rest of the engine combination are coordinated with the turbocharger. A compatible boost fooler or overboost code regulator is required because the higher actuator setting can allow boost pressure to exceed the range expected by the factory PCM and trigger an overboost-related fault.

Stage 1 is best suited to a tuned street truck, performance-oriented tow build, or moderately modified combination that can use the additional turbine-housing capacity but does not require the Stage 2 turbo’s 66mm compressor, larger 76/70mm turbine, 4-inch inlet, and ball-bearing center section.

It should not be selected solely because the name “Stage 1” sounds better than “Stock Plus.” On an otherwise stock truck, the 1.0 A/R housing and 30 PSI control hardware may add requirements without delivering the improvement an owner expects. The decision should be based on the truck’s injectors, calibration, fuel delivery, exhaust energy, towing use, current airflow demand, and future build plan.

SPOOLOGIC SL-100-009 Stage 2 Turbocharger

The SPOOLOGIC SL-100-009 Stage 2 GTP38 and GTP38R Turbocharger is a complete higher-output package rather than a stock GTP38 with only a larger compressor wheel. It combines a 66/88/94mm 6+6 billet aluminum compressor wheel, 4-inch anti-surge compressor inlet, upgraded 76/70mm turbine wheel, 1.0 A/R turbine housing, hybrid ceramic dual ball-bearing cartridge, finned aluminum center section, ceramic-coated turbine housing, non-EBPV pedestal and outlet, and upgraded 30 PSI wastegate actuator.

The larger compressor provides the airflow capacity needed by increased-fueling combinations, while the larger turbine gives the exhaust side more flow capacity than the factory-style turbine used in the lower three tiers. The 1.0 A/R housing provides additional exhaust-flow capacity, and the anti-surge compressor housing broadens the useful compressor operating range.

The hybrid ceramic dual ball-bearing cartridge reduces friction compared with a conventional journal-bearing arrangement. The finned aluminum center section is designed to transfer and reject heat more effectively around the bearing area, while the ceramic-coated turbine housing helps retain exhaust energy in the turbine side and reduce radiant heat around nearby underhood components.

Custom tuning is required for Stage 2. It is not designed to operate correctly on a factory calibration, and it should not be treated as a turbo-only upgrade for an otherwise stock truck. A qualified 7.3L Powerstroke tuner must match the turbocharger to the injectors, fuel-delivery system, high-pressure oil system, intake, exhaust, and intended use. A compatible boost fooler is also required. SPOOLOGIC does not provide a proprietary calibration file; the tuner should calibrate the complete vehicle combination rather than selecting a generic tune based only on the words “Stage 2.”

Although the turbocharger mounts in the factory GTP38 location and includes the correct non-EBPV pedestal and outlet arrangement, the 4-inch compressor inlet and increased airflow capacity require additional planning. A compatible high-flow intake, leak-free bellowed up-pipes, free-flowing exhaust, secure charge-air boots and clamps, adequate fuel supply, sufficient high-pressure oil delivery, appropriate injectors, and boost and exhaust-gas-temperature monitoring should be treated as parts of the build.

Stage 2 is the right choice when the truck already has, or is being built around, the systems needed to use that additional airflow. It is not the right choice when the only goal is to replace a failed factory turbo on a stock-fueled daily driver.

Specialty Option: SPOOLOGIC SL-100-010 Non-Wastegated Turbocharger

The SPOOLOGIC SL-100-010 Non-Wastegated Performance Turbocharger is a separate specialty option rather than another step in the Stock, Stock Plus, Stage 1, and Stage 2 progression. It uses a 60/80/84mm 5+5 billet aluminum compressor wheel, upgraded journal-bearing internals, a 1.15 A/R non-wastegated turbine housing, and non-EBPV pedestal and outlet hardware.

Because the turbine housing does not use a wastegate, all exhaust flow is directed through the turbine wheel. The larger 1.15 A/R housing provides additional exhaust-flow capacity but also changes response compared with the smaller wastegated configurations. This turbo should be selected according to the engine’s fueling, exhaust energy, tuning, operating range, and intended use—not simply because a non-wastegated housing appears simpler.

Custom tuning is recommended so fueling and engine operation are matched to the non-wastegated turbine configuration. The SL-100-010 is most appropriate for an owner or builder who specifically wants a non-wastegated setup and understands the response and system-matching considerations that come with the 1.15 A/R housing. Stock Plus or Stage 1 will usually be the more straightforward choice for a conventional street or tow build that benefits from wastegate control.

Which 7.3L Powerstroke Turbo Should You Choose?

Choose the SL-100-006 Stock Turbo If You Want Factory-Style Operation

Select the SL-100-006 Stock turbo when reliability, factory-style response, original EBPV operation, straightforward replacement, and predictable towing or work-truck behavior matter more than additional airflow capacity. This is the best match for a stock restoration, fleet vehicle, daily driver, or customer who is satisfied with factory power and does not want to redesign the rest of the combination.

Choose the SL-100-007 Stock Plus If You Want the Best Mild Upgrade

Select the SL-100-007 Stock Plus turbo when the truck is stock or mildly modified and the goal is a responsive billet-wheel upgrade without moving into a 1.0 A/R turbine housing, 30 PSI actuator, mandatory boost-fooler hardware, or larger performance-turbo build. It is especially well matched to daily drivers and tow trucks that benefit from a mild airflow improvement but still spend most of their time in the operating range where the factory-style turbine configuration responds quickly.

Choose the SL-100-008 Stage 1 If the Truck Is Tuned and Needs More Turbine Capacity

Select the SL-100-008 Stage 1 turbo when the truck has custom tuning or a planned custom calibration, the fuel and injector combination can use the 1.0 A/R turbine housing and 30 PSI actuator, and the owner wants to retain a factory-style GTP38 turbine wheel. Plan for the required boost fooler and work with a qualified tuner. Stage 1 is a system-matching decision, not simply the next item in a catalog hierarchy.

Choose the SL-100-009 Stage 2 for a Fully Supported Higher-Output Build

Select the SL-100-009 Stage 2 turbo when larger injectors, adequate fuel delivery, sufficient high-pressure oil supply, a 4-inch intake, upgraded exhaust flow, sound up-pipes, secure charge-air plumbing, monitoring, and custom tuning are already installed or included in the build plan. Its larger compressor, larger turbine, 1.0 A/R housing, anti-surge inlet, and ball-bearing center section provide capacity the lower tiers do not, but that capacity only becomes useful when the engine and calibration can drive it correctly.

Choose the SL-100-010 If You Specifically Need a Non-Wastegated Configuration

Select the SL-100-010 Non-Wastegated turbo when the build specifically calls for a 1.15 A/R non-wastegated turbine housing and the engine’s fueling, exhaust energy, tuning, and intended operating range are matched to that configuration. It should be treated as a specialty option rather than a universal upgrade above Stage 1 or below Stage 2.

Supporting Modifications That Matter Before a Turbo Upgrade

Even the best turbocharger cannot correct problems elsewhere in the engine’s air, exhaust, fuel, or oil systems. Before replacing or upgrading the turbo, inspect the up-pipes and exhaust inlet connections for pre-turbo leaks. Exhaust escaping before the turbine reduces the energy available to drive the turbo and can cause slow spool-up, low boost, smoke, and poor towing performance.

Inspect the intercooler boots, intake plenums, clamps, crossover connections, and intercooler for charge-air leaks. A turbo may be producing airflow correctly while a leaking boot, clamp, plenum, or charge-air component prevents that air from reaching the cylinders.

Oil condition and oil supply are equally important. The turbocharger depends on clean oil delivered at the correct rate and an unrestricted drain path. Contaminated oil, sludge, debris, a restricted feed, or a poor drain can damage a new turbo regardless of its performance tier. The engine’s crankcase-ventilation system, air filter, intake tube, and compressor inlet should also be inspected so the new turbo does not ingest debris or operate against unnecessary restriction.

Stage 1 and Stage 2 require additional planning. The 30 PSI actuator used on both models requires a compatible boost fooler, and the engine calibration must be appropriate for the truck’s complete combination. Stage 1 carries a strong custom-tuning recommendation; Stage 2 requires custom tuning.

Stage 2 also requires a fuel and high-pressure oil system capable of supporting the selected HEUI injectors, an intake compatible with its 4-inch compressor inlet, a free-flowing exhaust, leak-free high-flow up-pipes, and charge-air components capable of remaining sealed at the intended boost level. The non-wastegated SL-100-010 should likewise be matched to the truck’s fueling, tuning, and exhaust-energy requirements.

Higher engine output places more load on the transmission, clutch, cooling system, and driveline. Those systems should be considered before the turbo is selected rather than after the truck exposes the next weak point.

What Is the Best Turbo for Towing?

For a stock or nearly stock tow truck, the Stock or Stock Plus turbo will usually be the better match. Both retain a responsive factory-style turbine configuration and approximately 22 PSI actuator. The Stock version preserves the EBPV and original exhaust arrangement, while Stock Plus adds a 60/80/84mm 5+5 billet compressor and deletes the EBPV. The correct choice between them depends on whether factory cold-weather warm-up operation or the simplified non-EBPV exhaust arrangement is more important to the owner.

Stage 1 can work well in a properly tuned tow-oriented build with additional fueling, but it is not automatically a better towing turbo simply because it has a higher stage designation. Its 1.0 A/R turbine housing and 30 PSI actuator must be matched to the complete combination. The calibration must manage fueling and boost cleanly, and the driver should monitor exhaust-gas temperature under sustained load.

Stage 2 should be chosen for towing only when the truck is a fully supported performance build that genuinely needs its airflow and exhaust-flow capacity. The SL-100-010 should also be reserved for combinations specifically suited to its 1.15 A/R non-wastegated housing. An oversized or poorly matched turbine configuration can respond slowly at lower engine speed, produce more smoke before reaching its efficient operating range, and create worse towing behavior than a smaller turbo correctly matched to the fuel and load.

Do not choose a towing turbo by the highest advertised boost number. Boost pressure is only one measurement and does not directly reveal compressor efficiency, turbine drive pressure, delivered air mass, exhaust temperature, or whether the calibration is adding the correct amount of fuel. A well-matched lower-tier turbo can be a better towing combination than a larger turbo operating below its intended range.

Common 7.3L Turbo Upgrade Mistakes

Buying by stage name alone: Stage 2 is not automatically better for every truck. The correct turbo is the one matched to the engine and intended use.
Assuming Stock Plus and Stage 1 use different compressor wheels: The SL-100-007 and SL-100-008 both use a 60/80/84mm 5+5 billet compressor. Stage 1 is differentiated by its 1.0 A/R turbine housing and 30 PSI actuator.
Expecting the turbo alone to create a fixed horsepower gain: Power depends on airflow, fueling, high-pressure oil supply, tuning, engine condition, and the complete combination.
Installing Stage 2 on a factory calibration: The SL-100-009 requires custom tuning and is not designed as a stock-tune turbo-only upgrade.
Forgetting the boost fooler: The 30 PSI actuator on Stage 1 and Stage 2 can exceed the pressure range expected by the factory PCM. Compatible overboost-control hardware is required.
Ignoring the EBPV difference: The Stock turbo retains the factory EBPV. Stock Plus, Stage 1, Stage 2, and the non-wastegated SL-100-010 include non-EBPV hardware.
Ignoring pre-turbo and charge-air leaks: Leaking up-pipes, intercooler boots, plenums, or clamps can make a healthy new turbo appear slow or weak.
Ordering the wrong 1999 configuration: Early 1999 and Late 1999 turbo systems are not direct-fit substitutes for one another. Use the Early 1999 vs. Late 1999 identification guide before ordering.
Choosing by boost pressure alone: More boost does not automatically mean more useful airflow, lower exhaust temperature, or more power.
Overlooking the Stage 2 inlet: The 4-inch anti-surge compressor inlet requires a compatible intake arrangement.
Treating the SL-100-010 as another numbered stage: The non-wastegated turbo is a specialty configuration that must be matched to the truck’s fueling, tuning, exhaust energy, and intended use.

Emissions and California Sales Notice

Emissions requirements can vary by turbocharger, vehicle configuration, and location. Review the emissions notice on the applicable SPOOLOGIC product page before purchasing or installing a performance turbocharger. Customers are responsible for confirming the emissions and vehicle-use requirements that apply in their location.

Frequently Asked Questions

What Is the Best Turbo for a Stock 7.3L Powerstroke?

The SL-100-006 Stock is the best choice when the truck is stock and the owner wants factory-style performance, wastegate operation, EBPV function, and drivability. The SL-100-007 Stock Plus is the better choice when the owner wants a mild billet-wheel upgrade and non-EBPV exhaust configuration while retaining the responsive factory-style turbine setup.

What Is the Difference Between Stock Plus and Stage 1?

Stock Plus and Stage 1 both use a 60/80/84mm 5+5 billet compressor wheel. Stock Plus uses an approximately 22 PSI actuator and a more conservative factory-style turbine configuration. Stage 1 uses a 1.0 A/R turbine housing and upgraded 30 PSI actuator. Stage 1 requires a boost fooler and strongly recommends custom tuning, placing it above Stock Plus in turbine capacity, boost-control range, and supporting requirements—not compressor-wheel size or blade count.

Does the Stage 1 Turbo Use a 7+7 Compressor Wheel?

No. The SL-100-008 Stage 1 turbo uses a 60/80/84mm 5+5 billet compressor wheel. The standalone SPOOLOGIC 7+7 replacement compressor wheel is not used in this complete turbocharger.

Does the Stage 1 Turbo Require Custom Tuning?

Custom tuning is strongly recommended for the SL-100-008 so fueling, boost control, injectors, and the rest of the truck are matched to the 1.0 A/R turbine housing and 30 PSI actuator. A compatible boost fooler is required. SPOOLOGIC does not provide the custom calibration; the truck should be tuned by a qualified 7.3L Powerstroke calibrator.

Can the Stage 2 Turbo Be Installed on Stock Injectors?

The SL-100-009 mounts in the factory turbo location, but it is designed for higher-output combinations with increased fueling and the supporting systems needed to use its additional airflow. On a stock-fueled truck, much of that capacity would go unused, while the owner would still need custom tuning, a boost fooler, a compatible 4-inch intake, and the rest of the supporting hardware. Stock, Stock Plus, or Stage 1 is usually a more appropriate match unless a larger-injector build is planned.

When Should I Choose the Non-Wastegated SL-100-010?

Choose the SL-100-010 when the build specifically calls for a 1.15 A/R non-wastegated turbine housing and the engine’s fueling, tuning, exhaust energy, and intended operating range are matched to that configuration. It is a specialty option rather than the automatic next step after Stage 1.

Will a Larger Turbo Lower Exhaust-Gas Temperature?

A correctly matched higher-flowing turbo can provide the air needed to support additional fuel more cleanly and may help control exhaust temperature in a properly calibrated combination. A larger turbo does not guarantee lower EGT. If it is oversized, underdriven, leaking boost, paired with excessive fuel, or tuned poorly, response and exhaust temperature can become worse. EGT should be evaluated together with fueling, boost, load, engine speed, intake restriction, exhaust restriction, and probe location.

Which SPOOLOGIC Turbo Retains the Factory EBPV?

The SL-100-006 Stock turbo retains the factory exhaust back-pressure valve arrangement. The SL-100-007 Stock Plus, SL-100-008 Stage 1, SL-100-009 Stage 2, and SL-100-010 Non-Wastegated turbo include non-EBPV hardware.

Do Stage 1 and Stage 2 Require a Boost Fooler?

Yes. Both models use an upgraded 30 PSI wastegate actuator, which can allow boost pressure to exceed the range expected by the factory PCM and trigger an overboost-related fault. The boost fooler addresses that factory monitoring limitation, but it does not replace the tuning needed to coordinate fueling and engine operation.

Is the Wastegate Actuator Rating the Same as Actual Boost?

No. The actuator rating describes the wastegate-control hardware. Actual boost depends on tuning, engine load, injector output, exhaust energy, intake and exhaust restriction, elevation, wastegate control, and the condition of the charge-air system. The truck should be monitored and calibrated as a complete system rather than driven toward a single boost number.

Related 7.3L Powerstroke Guides

The Bottom Line

The SPOOLOGIC 1999.5–2003 7.3L Powerstroke turbo lineup provides four primary wastegated choices plus one specialty non-wastegated configuration. The SL-100-006 Stock restores factory-style operation and retains the EBPV. The SL-100-007 Stock Plus adds a 60/80/84mm 5+5 billet compressor and non-EBPV exhaust configuration while remaining a responsive mild upgrade.

The SL-100-008 Stage 1 uses the same 60/80/84mm 5+5 billet compressor dimensions as Stock Plus but adds a 1.0 A/R turbine housing and 30 PSI actuator for tuned, moderately modified combinations. The SL-100-009 Stage 2 adds the larger 66/88/94mm 6+6 compressor, upgraded 76/70mm turbine, 1.0 A/R housing, 4-inch anti-surge inlet, ceramic dual ball-bearing cartridge, and supporting capacity required by a properly built higher-output truck.

The SL-100-010 provides a separate 60/80/84mm 5+5 billet, journal-bearing configuration with a 1.15 A/R non-wastegated turbine housing for builds specifically suited to that arrangement.

Choose the turbo that matches the truck you actually have and the build you are prepared to complete—not the highest stage number available. Before ordering, document the engine build date, current injectors, fuel-system modifications, high-pressure oil-system condition, tuning, intake, exhaust, up-pipes, charge-air system, towing use, and realistic power goal.

Customers who are unsure which configuration fits their truck can contact SPOOLOGIC at 844-266-7800 with that information before placing the order.