SPOOLOGIC Stage 2 Performance Turbocharger

The SPOOLOGIC Stage 2 GT37 Turbocharger SL-100-045 is a performance upgrade for 2015-2019 Ford F-250 F-350 F-450 pickups with the 6.7L Powerstroke. Its larger billet compressor wheel gives higher-output street builds additional airflow capacity while retaining the factory exhaust connections, supporting approximately 650-700 rear-wheel horsepower with matched tuning, fueling, and supporting modifications.

⚠️ Custom tuning required before operation. See tuning requirements below.

Features

• Brand new, no core charge
• Direct-fit package with mounting adaptation for the listed applications
• 7+7 billet aluminum compressor wheel
• 10-blade turbine wheel
• Upgraded journal bearings, 360° thrust bearing, and step-gap seal rings
• New VGT control solenoid with factory-style vane cage and unison ring
• Ceramic-coated turbine housing and center-section exterior
• Raw, red, or black compressor housing options
• High-speed VSR balanced

What's Included

• 1 SPOOLOGIC Turbocharger — SL-100-045
• 1 SPOOLOGIC VGT Control Solenoid
• 1 SPOOLOGIC Ceramic-Coated Conversion Pedestal — SL-340-015
• 1 SPOOLOGIC Turbo Coolant Feed Line Kit — SL-360-003
• 1 SPOOLOGIC Turbo Mounting Gasket Kit — SL-310-161
• 2 SPOOLOGIC Up-Pipe-to-Turbo V-Band Clamps — SL-330-013
• 1 SPOOLOGIC Turbo-to-Downpipe V-Band Clamp — SL-330-015

Fitment

• 2015-2019 Ford F-250 F-350 F-450 Pickup 6.7L Powerstroke
• 2017-2019 Ford F-350 F-450 F-550 Chassis Cab 6.7L Powerstroke

Compare related configurations: SPOOLOGIC SL-100-044 Stage 1 turbocharger.

Tuning and Supporting Modifications

⚠️ Custom Tuning and Supporting Modifications: Custom tuning is required before operating the vehicle. Fuel delivery, intake airflow, charge-air capacity, and exhaust flow must be matched to the intended power level. Additional upgrades may be needed to achieve the listed power-support range; the turbocharger alone does not produce that output.

Supporting Modifications: Upgrade components as needed to support your intended power level.

• Larger injectors and fuel-system upgrades may be needed to reach the listed power range.
• Intake and intercooler upgrades may be needed to reach the listed power range.
• Adequate exhaust flow and sealed exhaust connections.
• Boost and exhaust-gas-temperature monitoring during setup and loaded operation.

SPOOLOGIC does not provide custom tuning services. Customers are responsible for arranging application-appropriate tuning with a qualified tuning provider.

Power Support

Approximately 650–700 rear-wheel horsepower with a properly matched build. This is total power-support capacity, not a promised horsepower increase. Actual output depends on engine condition, fuel delivery, calibration, and the complete vehicle combination.

Pedestal and Coolant Feed Line

The SL-100-045 uses a GT37 journal-bearing design and retains the factory up-pipes, downpipe, intake manifold, and turbo inlet boot. The included 2017-2019-style pedestal and coolant feed line adapt it to 2015-2016 pickups. In the listed 2017-2019 applications, it fits the factory mounting arrangement.

Compressor Wheel

• Blade design: 7+7
• Compressor inducer: 65 mm
• Compressor exducer: 88 mm
• Extended tip: 90 mm
• Material: 5-axis CNC-machined billet aluminum

Turbine Shaft

• Turbine inducer: 72.5 mm
• Turbine exducer: 66 mm
• Turbine blade count: 10
• Material: High-nickel Inconel

Upgraded Internals

• Upgraded journal bearings
• 360° thrust bearing
• Step-gap seal rings

High-Speed VSR Balancing

The rotating assembly is high-speed VSR balanced before shipment for smooth, consistent operation.

VGT Control System

The turbocharger is assembled with a new VGT control solenoid and a factory-style 2017-2019 vane cage and unison-ring assembly. VGT-based exhaust-brake operation is supported, with actual exhaust-brake behavior dependent on the vehicle’s calibration and any exhaust-braking strategy programmed by the tune provider.

Coatings and Finish Options

The turbine housing, center-section exterior, and pedestal are ceramic coated to help manage radiant heat and resist oxidation. Heat reduction varies with operating conditions. The finish options below apply only to the compressor housing.

• Raw: Natural aluminum with no coating
• Red: Red powder-coated finish
• Black: Black powder-coated finish

Installation Notes

• Reuse the existing intake manifold, turbo inlet boot, and heat shield.
• Reuse the original pedestal-to-engine-block bolts.

OEM Cross-References

• Garrett: 888142-5001S
• Garrett: 888142-9001S
• Garrett: 888143-5001S
• Garrett: 888143-9001S
• Garrett: 892147-5001S
• Ford: FC3Z-6K682-A / FC3Z6K682A
• Ford: FC3Z-6K682-B / FC3Z6K682B
• Ford: HC3Z-6K682-A / HC3Z6K682A
• Ford: HC4Z-6K682-C / HC4Z6K682C
• Motorcraft: TC-71 / TC71

⚠️ Emissions Notice

Not CARB approved. Not legal for sale or use in the state of California.

1-Year Limited Warranty

Every SPOOLOGIC turbocharger carries a one-year limited warranty against defects in materials and workmanship from the original purchase date. Coverage applies to the original purchaser with dated proof of purchase. Contact SPOOLOGIC for return authorization before shipping the turbocharger for inspection. If inspection confirms a covered defect, SPOOLOGIC will repair or replace the turbocharger at its discretion. Coverage excludes damage caused by foreign-object debris, oil starvation, contaminated or restricted oil supply or drainage, extended oil-change intervals, overboosting, overspeed, overfueling, excessive exhaust temperatures, improper installation or startup, improper tuning or repairs, or operation outside the listed application or intended operating range. Normal cosmetic wear, coating discoloration, and heat-cycling marks are not covered. Customers pay shipping to SPOOLOGIC and return shipping, whether the claim is approved or denied. Labor, diagnostics, removal, reinstallation, towing, downtime, and other related expenses are not covered. See the SPOOLOGIC Warranty Policy for complete terms and claim procedures.